Car parking area and arrangement of parking for cars (60 photos)
When we go to the country, we want to have a quiet and pleasant time with family or friends. Summer residents don't need extra worries. Therefore, you need to think in a timely manner about the question of where your favorite car will be located in order to keep it intact and safe. After all, no one wants to run to the side of the road every hour and check the condition of the car.
In this article, we will tell you what the device of the car platform is and how to make it with your own hands.
The most budget option, which does not require additional efforts to organize parking, is the construction of an open-type site. Of course, you will not be able to protect the car from precipitation, but you will save on the construction of a frame for a canopy and the implementation of its shelter.
The main problem of the cottager will also be solved – ensuring the safety of the car and property when you are on the territory of the dacha settlement. You can easily enter the territory of your allotment and leave it, but only you will have access to the vehicle.
An open area for a car in the country is being arranged on the territory of the land plot. The place should be flat and provide ease of arrival and departure. But moisture should not stagnate there.
If the territory is fenced, guarded, then it is better to park right at the entrance gate. So you will not need to equip a wide and solid entrance to the house.
When the security issue is not resolved, then a place is chosen near the house – by the wall. It will cover from the wind and side rain with snow. The car will be safer, but you will lose some area of land that you could use, for example, for a vegetable garden or a flower bed.
Eco-stand with grass
If you want to equip the most natural parking option, then you should level the site and remove a small layer of natural soil. Crushed stone is filled to the bottom with a layer of up to 10-15 cm, and on top of it – sand 5-10 cm.
Geotextile can be laid between the layers, as well as on the sand. A lawn grid is laid on top. It should then be covered with fertile soil and sown with grass.
Use of crushed stone
A more economical and practical option is to fill the site with ordinary rubble. First, it is necessary to remove the upper fertile layer of soil. Instead, sand is laid, setting a curb restriction along the perimeter. It will ensure the preservation of the shape of the structure.
After fixing the sidewalk curbs, it is necessary to lay crushed stone on top of the sand with a layer of 15 cm . Moreover, it is necessary to raise the level above the ground. To facilitate the movement of cars on the site in the center, two strips of concrete slabs are laid under the wheels.
This is a more durable and reliable construction option. However, it will suit you only if the soil is not subjected to heaving. The fertile layer of soil is cut off, sand is filled in its place, and then the formwork is installed.
For strength, a reinforcing mesh is placed on top of the sand. The concrete platform is filled with mortar so as to create a layer of 5 cm. Without letting the mixture dry completely, another level of the reinforcement structure is laid. Concrete is poured from above in 5 cm .
For a heavier car, such as an SUV, the total height of the concrete platform can be increased to 15 cm.
Laying paving slabs
Paving slabs can serve as an alternative to concrete. It will be indispensable for the arrangement of the site on the ground, which is subjected to heaving. Thanks to the gaps between the blocks, the parking surface will not be disturbed. Also, with such a coating, faster evaporation of moisture is provided.
The tile is laid on a mixture of sand and cement. As a base, you can use tightly packed small crushed stone. For better grip, the blocks are pressed down with a rubber-coated mallet.
You can evaluate the features of using various materials and the appearance of the structure in the photo of the car platform.
Parking equipment with a canopy
If you live in a country house permanently or often and come to the country for a long time, it is advisable to equip a more capital site for a car. Such a structure should protect the car not only from intruders, but also from the effects of natural factors – precipitation and direct sunlight.
Our step-by-step instructions on how to make a platform for a car will help you to carry out the work on the arrangement yourself.
Choosing a location near the entrance gate or close to the access road will allow the car to easily drive in and turn around. In addition, natural moisture removal will be provided.
It is also necessary to pre-calculate the size of the site. An area of 3x6 m is sufficient for passenger vehicles . But a larger car will need a territory size of 4x11 m.
At the initial stage of work, pegs should mark the perimeter of the future parking lot. Pull the string between the pegs. On the marked area, the top layer of soil is removed. In its place , a special pillow is formed from several layers:
- gravel – more than 50 mm.
Arrangement of the formwork
In order for the concreting of the site to be of the highest quality, it is necessary to exclude the presence of pits and bumps on the surface. The formwork is made of boards with a width of 200-300 mm. Metal pegs 400-500 mm driven into the ground on both sides of the formwork will prevent its fall. The step of such fastening is about half a meter. At the edges of the boards, their reliable fixation is required to avoid leakage of the solution.
The solution is leveled by a rule, the standard length of which is up to 1.5 m. Since the platform itself will be much larger, it is desirable to provide for the installation of additional guides. The embedded elements are aligned in the transverse direction. Longitudinally, it is necessary to provide a slight slope in the direction of travel – up to 5 degrees. This way you will facilitate the removal of water from the site.
Reinforcement is required to strengthen the structure. For this purpose, a mesh with a wire up to 8 mm thick and a cell size of 100x100 mm is used. It is recommended to raise the reinforcing layer by 250 mm compared to the base or to do a two-level reinforcement.
The design for double reinforcement includes a mesh in two layers with 80 mm long jumpers. They are installed in 45-50 mm increments. It is advisable to use PVC clamps for connections.
All work must be done in one day, without leaving the solution the next day. During the day, the solution dries up and loses the ability to effectively grasp new layers.
The solution can be prepared manually or use a concrete mixer. The filling of the platform under the car is carried out evenly, but the concrete must be above the level of the guides.
The work is being carried out from a section removed from the road in the direction of the entrance. The concrete is laid flat. The rule is to level it. The entire volume within the formwork must be filled with mortar.
Upon completion of the work, the site is covered with a polyethylene film. This way you will eliminate cracking, and the drying itself will be more uniform. And precipitation and ordinary moisture will not get on the concrete surface.
The mixture dries after 5-6 days. The formwork needs to be disassembled and the pins removed. The edges of the platform are reinforced with metal corners. Such pads are attached to each other and to concreted rods by welding.
Arrangement of the canopy
For the construction of the roof, it is necessary to bend the support pipe with the desired radius. Such a beam is attached to vertical supports by bolts or by means of a welding machine. The use of a metal kerchief will give greater structural strength.
To fix the frame, you need to build a base. In its capacity, concrete columns can be used, which are fixed in the surface of the site. For the pillars, you can create a separate foundation of concrete by filling sand and gravel into the hole.
The frame is installed on the pillars of the base with the help of corners made of metal logs or profiled pipe. The roof is made of corrugated board or polycarbonate sheets. It is attached to the "skeleton" of the canopy. After that, all metal parts must be coated with an anti-corrosion solution and painted.
Wood can be used as a material for the manufacture of the frame. But the beam must be at least 50 mm thick with treatment with protective compounds.
To build a reliable and solid platform for a car in the country, it is worth working hard. You can choose the most suitable option for you – to arrange an open or hinged parking lot. But the benefits of such a decision will be obvious – a car protected from encroachments and external influences.
Photo of the site for the car